Explained clearly 6 min read

How to Report Uncertainty with the Correct Number of Significant Figures According to the GUM

The GUM recommends reporting expanded uncertainty with one or two significant figures, then rounding the measured value to the same decimal place. This article explains the rule, worked examples, common errors, and standards citations.

Short Answer

The GUM recommends reporting expanded uncertainty with one or two significant figures, then rounding the measured value to the same decimal place. This article explains the rule, worked examples, common errors, and standards citations.

The Guide to the Expression of Uncertainty in Measurement (GUM) gives a clear, practical rule for reporting measurement results: report the uncertainty to one or two significant figures, then round the measured value to the same decimal place. This site is a precision and rounding reference, not merely a significant figures calculator. The calculator is fast and accurate, but the rules below explain the reasoning, standards, and edge cases that matter in metrology, engineering, chemistry, physics, and laboratory accreditation.

Rule Statement

According to JCGM 100:2008 (GUM), clause 7.2.6, the numerical values of the estimate y and its standard uncertainty u(y) or expanded uncertainty U should not be given with an excessive number of digits. It is preferable to give only two significant digits for u(y) or U. The value of y should then be rounded to the last digit retained in the uncertainty.

In practice:

  1. Compute the standard uncertainty or expanded uncertainty using the appropriate model.
  2. Decide the coverage factor k (often k = 2 for approximately 95 % coverage).
  3. Round U to one or two significant figures. Two is the usual default; one may be used when the leading digit is large and the uncertainty is only indicative.
  4. Identify the decimal place of the last retained digit in U.
  5. Round y to that same decimal place.
  6. Report y, U, and k with units, e.g., m = 12.346 g, U = 0.023 g, k = 2.

Core rule: uncertainty and value share the same last decimal place, not the same number of significant figures.

Standards Citation

The GUM rule is reinforced by major metrology and laboratory standards:

  • JCGM 100:2008 (GUM), clause 7.2.6: recommends no more than two significant digits for uncertainty and requires the value to be rounded consistently.
  • NIST Technical Note 1297, Section 6.2: states that the reported value and its uncertainty should be rounded to the same number of decimal places, with two digits for uncertainty generally sufficient.
  • ISO/IEC 17025:2017, clause 7.8.3: requires testing and calibration reports to include uncertainty, with reporting consistent with the GUM and the customer’s requirements.
  • ASTM E29-13a: provides standard practice for using significant digits in test data and for rounding when determining conformance.
  • ISO 80000-1:2009, clause 7.3: gives general rules for rounding numerical values and expressing quantities.

These citations matter because different fields may impose stricter internal conventions, but the GUM remains the primary international reference for uncertainty expression.

Worked Examples

Each example starts with an unrounded value and expanded uncertainty. We apply the GUM rule from the original numbers to avoid double rounding.

Example 1: Mass measurement

Raw result: m = 12.34567 g, U = 0.0234 g, k = 2.

  1. Round U to two significant figures: 0.0234 g → 0.023 g.
  2. The last retained digit is in the third decimal place (0.001 g).
  3. Round m to the third decimal place: 12.34567 g → 12.346 g.

Report: m = 12.346 g, U = 0.023 g, k = 2.

Example 2: Voltage measurement

Raw result: V = 1.234567 V, U = 0.000456 V, k = 2.

  1. Round U to two significant figures: 0.000456 V → 0.00046 V.
  2. The last retained digit is in the fifth decimal place (0.00001 V).
  3. Round V to the fifth decimal place: 1.234567 V → 1.23457 V.

Report: V = 1.23457 V, U = 0.00046 V, k = 2.

Example 3: Concentration

Raw result: c = 5.6789 mg/L, U = 0.0123 mg/L, k = 2.

  1. Round U to two significant figures: 0.0123 mg/L → 0.012 mg/L.
  2. The last retained digit is in the third decimal place (0.001 mg/L).
  3. Round c to the third decimal place: 5.6789 mg/L → 5.679 mg/L.

Report: c = 5.679 mg/L, U = 0.012 mg/L, k = 2.

Counter-Examples

These illustrate common reporting errors and why they are inconsistent with GUM clause 7.2.6.

  • Over-reporting the value: m = 12.34567 g, U = 0.02 g. The uncertainty ends at the hundredth place, so the value should be 12.35 g, not 12.34567 g.
  • Mismatched decimal places: m = 12.3 g, U = 0.023 g. The uncertainty is in thousandths, but the value is in tenths. Correct: 12.346 g, U = 0.023 g.
  • Excess uncertainty digits: U = 0.02345 g. GUM prefers two significant digits, so report 0.023 g.
  • Rounding uncertainty too coarsely: U = 0.67 g → 1 g. That discards real information. Two significant digits: 0.67 g. One significant digit: 0.7 g.
  • Double rounding: first rounding U to 0.02 g, then rounding m to 12.35 g, then again to 12.4 g. Always round from the original raw values to the final decimal place in one step.

Convention Comparison Table

Convention or standard Uncertainty digits Value rounding Typical coverage factor
GUM (JCGM 100:2008, 7.2.6) One or two significant figures; two preferred Same decimal place as uncertainty k = 2 for ~95 %
NIST TN 1297 Two digits generally sufficient Same decimal place as uncertainty k = 2 for ~95 %
ISO/IEC 17025:2017 Follow GUM; often two digits Same decimal place as uncertainty As specified; often k = 2
ASTM E29-13a Practical rounding for conformance Round to declared precision Not a coverage-factor standard
ISO 80000-1:2009 General rounding rules Round once to target precision Not a coverage-factor standard

Common Mistakes

  • Reporting the value and uncertainty with the same number of significant figures instead of the same decimal place.
  • Keeping too many digits in the uncertainty because the software printed them.
  • Rounding the value before determining the final uncertainty decimal place.
  • Omitting units or the coverage factor k.
  • Using one significant figure for uncertainty when two are justified, or two when the leading digit is 1 and more digits would be misleading.
  • Confusing standard uncertainty u(y) with expanded uncertainty U.
  • Using a coverage factor that is not stated, making the result ambiguous.
  • Forgetting that trailing zeros in scientific notation are significant, e.g., 1.20 × 10−3 has three significant figures.

Quick Reference Table

Raw uncertainty U Reported U (2 s.f.) Last decimal place Raw value y Reported y Final report
0.0234 0.023 0.001 12.34567 12.346 12.346 ± 0.023
0.000456 0.00046 0.00001 1.234567 1.23457 1.23457 ± 0.00046
0.0123 0.012 0.001 5.6789 5.679 5.679 ± 0.012
0.123 0.12 0.01 10.456 10.46 10.46 ± 0.12
0.0994 0.099 0.001 1.2345 1.234 1.234 ± 0.099

This GUM rule connects directly to other precision and rounding topics on this site:

Our significant figures calculator is a precise tool, but these reference pages are designed to help you understand why a report is correct, not just to produce a number.

Sources & Further Reading

  • JCGM 100:2008, Evaluation of measurement data — Guide to the expression of uncertainty in measurement, clause 7.2.6.
  • NIST Technical Note 1297, Guidelines for Evaluating and Expressing the Uncertainty of NIST Measurement Results, Section 6.2.
  • ISO/IEC 17025:2017, General requirements for the competence of testing and calibration laboratories, clause 7.8.3.
  • ASTM E29-13a, Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications.
  • ISO 80000-1:2009, Quantities and units — Part 1: General, clause 7.3.

FAQ

Should uncertainty always have two significant figures?

No. The GUM says one or two significant figures are acceptable, with two generally preferred. One significant figure may be used when the leading digit is large or when the uncertainty is only indicative.

How do I round the measured value?

Find the decimal place of the last retained digit in the rounded uncertainty. Round the measured value to that same decimal place. For example, if U = 0.023 g, the last digit is in the thousandths place, so m = 12.34567 g becomes 12.346 g.

Can I report three significant figures for uncertainty?

Only in unusual cases where the uncertainty itself is the subject of study, or when a discipline explicitly requires it. For routine measurement results under the GUM, two significant figures are the recommended maximum.

Do I round before or after calculating expanded uncertainty?

Calculate with full precision, then round only at the final reporting step. Rounding intermediate uncertainty components can introduce bias and double-rounding errors.

What about relative uncertainty?

Relative uncertainty is often reported as a percentage. Round the relative uncertainty to one or two significant figures and state the value to which it refers. Do not mix absolute and relative forms ambiguously.

Verified sources

References

  1. JCGM 100:2008, Evaluation of measurement data — Guide to the expression of uncertainty in measurement (GUM), clause 7.2.6.
  2. NIST Technical Note 1297, Guidelines for Evaluating and Expressing the Uncertainty of NIST Measurement Results, Section 6.2.
  3. ISO/IEC 17025:2017, General requirements for the competence of testing and calibration laboratories, clause 7.8.3.
  4. ASTM E29-13a, Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications.
  5. ISO 80000-1:2009, Quantities and units — Part 1: General, clause 7.3.

Leave a Reply

Your email address will not be published. Required fields are marked *